How To Build An Outdoor Fire Pit With A Cover

This outdoor fire pit with a cover is an easy project for beginning and experienced DIYers alike. Keep warm outdoors in the cold months and utilise every bit a coffee table in the warmer part of the yr!

Although it'southward not cold very often where nosotros live, we exercise enjoy those evenings in the wintertime when we tin be outdoors (sans profuse sweat 🤣). During the holidays with the family unit hither, we did have a cold spell for a week and decided to build this easy garden fire pit. A cover was something that I felt necessary for several reasons. At that place can be critters around here at nighttime and we felt that they would be safer when poking around. Once nosotros snuff the fire with either water or dirt, we popular that hat on and not only does it forestall any issues but looks better aesthetically!

Hither nosotros were with some of the family roasting marshmallows and making south'mores…yum!!

Let'south become into the DIY build process and be sure to bookmark this if you think that this project is in your futurity.
This is a paid mail service in behalf of Spectrum Brands simply the work and opinions expressed hither are my own.

Outdoor Burn Pit With A Cover DIY

All of our projects here start with a program that nosotros sketch out. Information technology'due south so helpful to envision and feel gratis to print this out!

Materials

• 36″ Metal Fire Pit Insert Liner
• 52 pieces of 4″x xi.75″ x 6.75″ concrete retaining wall block
• Four – 8′ – ii ten 6's (pressure treated pine)
• One – viii′ – i 10 3 (pressure treated pine)
• Two – 36″ x 24″ pieces of metal sheeting (stainless steel)
• Two – National Hardware Back Flap Hinges
• 1 – National Hardware 8 1/2″ Biconvex Gate Pull
• one 1/iv″ Exterior deck screws
• Early American Stain

Tools

• Chop saw
• Jigsaw
• Spiral Gun
• Screwdriver
• Wrench (open up finish)
• Pair of metal snips
• Record measure
• Marker
• Pencil
• String
• 60 grit Sandpaper

DIY Fire Surround Instructions:

Step 1 –

Determine where you want to build your burn pit. Make sure that information technology'southward at to the lowest degree six′ away from any existing landscaping or structures and on flat ground. We built ours over a portion of our existing pea gravel patio area towards the back of our garden. Be sure to build your outdoor fire pit on a surface that will non burn (gravel, dirt, rock, etc).

Step 2 –

Gather the metal insert with a screw driver and wrench. I don't have an image of assembly, just it'south easy!

Step 3 –

Get-go placing the brick around the perimeter of the metallic fire insert. Each layer requires xiii brick to go around the circumference of the fire pit insert. We built this DIY burn down pit to be iii layers tall, but yous can add more than layers if desired.

DIY Outdoor Fire Pit Cover Instructions

Stride 1 –

Cut four viii′- ii x 6's in half with a saw. Yous will then take eight pieces measuring 4′ long. Cut the 8′ – 1 x 3 into four pieces that will be two′ in length.

Pace 2 –

Place the eight pieces on top of the fire pit, completely roofing the top. Place the four 1 x 3'due south on height to decide their final length. They will need to be trimmed with the jigsaw.

Step 3 –

Discover the middle of the wood that you've now placed on pinnacle of the fire pit using your measuring record.
You volition then need a brusk length of string and a pencil to marking a radius around the edge to circular off the woods for the top.

Step 4 –

Using a jigsaw, cut the radius of the wood that you've marked around the edge of the fire pit. Trim the i ten iii'due south to match the edge.

Step 5 –

Turn the top over. You'll then be attaching the metal sheeting to the underside of the wood. Measure the metal sheeting and mark with a marker to match the radius of the top. The metal sheet will need to cover the inside of the fire pit simply. Attach with the same screws that yous've been using in this projection.

Stride 6 –

After you've fastened the metal to the underside of the top, flip information technology over. Adhere the iv 1 x iii's to the 2 ten 6's with 1 i/4″ deck screws. Be sure to offset the 1 10 three″due south. NOTE: The top volition exist hinged so yous don't want the woods to overlap.

Step vii –

Attach the National Hardware Dorsum Flap Hinges to the meridian heart. By attaching this way you'll exist able to access the outdoor burn down pit without removing the lid!

Step 8 –

Stain or paint the pinnacle to protect the wood, as desired. We brushed on an early American stain and wiped it down.

Stride nine –

Adhere the National Hardware 8 ane/2″ Biconvex Pull to one side of the top. You could use two handles if preferred.

As you tin can come across, the lid is hinged and the National Hardware Pull helps when y'all want to motility the chapeau on or off!

Such a fun project for the whole family and i that requires no maintenance over the years. A dark of s'mores!

BONUS! – How To Make The Best Fire Starters

This is what we did when I was a girl scout leader and it's the best way to first a campfire! Fill an empty cardboard egg carton (not styrofoam) with either dryer lint, sawdust (salve from cutting your wood!) or shredded paper. I used a combination of dryer lint and paper shreds. Heat up plain canning wax in a double boiler and in one case melted pour over each filled egg holder. One time the wax is cooled and dry, cut the sections apart. You'll need 2 or three in your fire pit and nosotros put them under the kindling. Light the burn starters and you'll soon accept a make clean burn down and glorious burn down that needs only fresh wood logs as the nighttime goes on!

PIN THIS POST!

yuegary2001.blogspot.com

Source: https://shabbyfufu.com/outdoor-fire-pit-with-a-cover-diy/

Share this post